Tube Preamp (2 x 12AX7) - Driver Tubes (2 x 12AX7 & 12AU7) - Tube Power Amp (6 x 6550 tubes) - 300 watts @ 2 ohms - 300 watts @ 4 ohms - 3 Band EQ - Five Position Mid Tone Control - Ultra Low Boost - Ultra High Boost - Balanced Line Out - Preamp Out/Power Amp In - Normal & Padded Input - Tube Protection Circuitry - Auto-Fault Mode - Fan Cooled - Slave Output Jack - 4/2 Ohm Impedance Selector - User Biasing Control.

All-Tube Preamp (5 x 12AX7) - Driver Tubes (2 x 12AX7, 12AU7) - Tube Power Amp (6 x 6550) - 300 Watts @ 2 0hms - 300 Watts@ 4 0hms - 3 Band EQ - Five Position Tone Control - 9 Band Graphic EQ - Ultra Low Boost - Ultra High Boost - Balanced Line Out - Effects loop - Preamp Out/Power Amp In - Unique Tube Drive control - Input Peak LED - Input Pad & Bright Switch - Mute Function - Tuner Out - Time-Delayed Turn-On - Defeatable Optocoupler Limiters - Hih Capacity Fan

8x10" (800 Watts RMS) - 2" Voice Coil - 30 oz. Magnets - Frequency Response (-3dB): 60-5kHz - Useable Low Frequency(-10dB: ) 42Hz - Nominal Impedance: 4 Ohms - Sensitivity: 100 dB/spl - Maximum SPL: 130 dB/spl

200 watts, 15"

300 watts rms, 15" Eminence speaker. Features: 3-band EQ with sweepable mid, high frequency boost/cut, low frequency boost/cut, high frequency enhance, low frequency enhance, volume, selectable Delta Comp(tm) Limiter, EFX loop, external speaker jack, fan cooling.

45 watts, four 10" spkrs with Alnico magnets. Controls that go to "12".

300 watts into 4 ohms and 100 watts into 8 ohms, that can biamp, or run full range out of both stages.

Straight ahead mono head that delivers a hefty 500 watts into 4 ohms.

1000 watts into 4 ohms (two 8 ohm cabs, a very usable, efficient set-up). Stereo or Biamp modes put 500 watts per channel into 2 ohms.

Dual-Chamber, Dual-Ported Cabinet - Four Hartke XL 10" Aluminum-Cone Bass Drivers - Power Handling: 400 Watts @ 8 Ohms - Frequency Response: 30 Hz To 5 kHz

Specially Tuned, Duct-Vented Cabinet Design - Precision Hartke XL 15" - Aluminum-Cone Bass Driver - Power Handling: 200 Watts @ 8 Ohms - Frequency Response: 30 Hz To 2.5 kHz

"Expanded-Design" Tuned, Ported Cabinet - Custom Hartke 5" Aluminum-Cone High-Frequency Driver - Four Hartke XL 10" Aluminum-Cone Bass Drivers - Power Handling: 400 Watts @ 8 Ohms - Frequency Response: 30 Hz To 12 kHz

350 Watts Per Side at 4 Ohms, 240 Watts Per Side at 8 Ohms, Selectable Tube & Solid-State Preamps, Rotary Bass & Treble Contour Controls, 10-Band Graphic Eq
Adjustable Compression, Variable Active Crossover W/ Balance Control, Effects Send & Return

400 Watt RMS amplifier that delivers peaks of 4000 Watts.

4x10 with horn (800 Watts RMS, 4 Ohms). - Dimensions (mm): H 698 x W 698 x D 380. Weight : 57Kg.

2x15 (600 Watts RMS, 4 Ohms). - Dimensions (mm): H 1000 x W 698 x D 489 - Weight : 64Kg.

4X10" (200 Watts with Horn).

1x15 (200 Watts, with Horn).

500 Watts, All Tube, Class A/B Power / 12x6L6-427, 4x12AX7 Two Inputs w/Independent Pull Bright Volume Controls, (1=Active, 2=Passive) - Pull Shift Bass & Treble Controls (Standard Mid Control) - Assignable 7 Band Graphic EQ - Dual Patch Point FX Loop (Front & Back) w/Blend Control - 600 Ohms XLR Balanced Out
3-Speed Fan Cooled (Off, Low & High).

2x10" - 300 Watts - Basis EVM Speakers

2x15"B4 - 800 Watts - 4 Ohms

1x15" - 400 Watts - 8 Ohms

1x12" + 4x8" - 900 Watts - 4 Ohms

150 watts RMS into 4 ohms - DDT compression - 15" Sheffield® speaker OR 15" Black Widow® 1502-4 DT speaker (TNT 115BW model) - Single channel - 7 band graphic EQ with push in/out - Variable crossover--200 Hz to 2 kHz with low and high/chorus outputs - Chorus rate and depth controls.

350 watts RMS into 4 ohms - 600 watts RMS into 2 ohms - 9 band graphic EQ with high and low active shelving controls - Compressor/limiter with level and compressor/limiter controls and LED indicator switchable with push switch or footswitch - Low-level FX loop - Variable electronic crossover with high/low relative balance control and high, high chorused, and low output jacks.

350 watts RMS into 4 ohms - 500 watts RMS into 2 ohms - 2-rack space design
1/4" input with passive/active push button - 2 channels - Solid state channel, pre gain control with clip indicator - Tube channel (12AX7 preamp tube), pre and post gain controls - Push channel select (footswitchable) and push channel combine switches - 7 band graphic EQ with active high and low shelving controls - Push graphic EQ in/out switch (footswitchable) - Master volume control - Post-EQ FX loop (footswitchable) - Variable crossover (100 Hz to 1 kHz) with balance control and frequency control.

350 watts RMS into 4 ohms - 600 watts RMS into 2 ohms

350 watts RMS continuous - 700 watts RMS program - Available with 4 or 8 ohms
4x10" Sheffield® bass speakers

400 watts RMS continuous - 800 watts program - 4 ohms - 8x10" Sheffield® bass speakers - Horn-loaded tweeter with L-pad attenuator and crossover
Crossover point 3.5 kHz.

100 watts RMS - 15"

300 watt amplifier head. Valve/solid state preamp section. 12 band graphic EQ. Harmonic Emphasis. Switchable, variable valve gain. Switchable pre-shape curve. Noise reduction. Dual compressor. Electro-luminescent front panel. Full range effects loop. Pre/post EQ balanced DI outputs. Tuner output. Fan cooled.

500 watt amplifier head. Valve/solid state preamp section. 12 band graphic EQ. Harmonic Emphasis. Switchable, variable valve gain. Switchable pre-shape curve. Noise reduction. Dual compressor. Electro-luminescent front panel. Two stereo effects loops - one full range, one high pass. Pre/post EQ balanced DI outputs. Tuner output. Fan cooled. MIDI control optional. Five way foot-controller optional.

400 watt RMS valve amplifier head featuring V-Type preamp. All valve power stage with 6x KT88 valves. Pre/post EQ DI output. Output impedance switchable 2 or 4 ohms. Effects loop. Line out .

320 watt RMS 4x10" cabinet with HF Horn (1048 without horn also available).
Impedance 8 ohms - Individual Driver Frequency Response 45Hz - 7kHz

300 watt RMS 1x15" cabinet. Impedance 8 ohms - Individual Driver Frequency Response 32Hz - 6kHz

400 watt RMS 2x15" cabinet. Impedance 4 ohms - Individual Driver Frequency Response 32Hz-5kHz

600 watt RMS 8x10" cabinet. Impedance 8 ohms.

500 Watts @ 4 Ohms - 400 Watts @ 8 Ohms - 250 Watts @ 16 Ohms - Hi and low sensitivity inputs - Gain control with LED peak clipping indicator - Limiter with variable threshold control - Stereo and Mono Effects Loop - Balanced XLR Output with select switch for Line or Direct Mode, ground lift & pad control - High and Low Crossover Outputs - Power Amp Assign Switch selects Bridge or Stereo Mode

4x10" - Impedance: 8 ohms @ 600 Hz - Power Handling Capacity: 700 Watts Continuous Program, 500 Watts RMS continuous pink noise, 40 Hz to 10K Hz, 8 hours - sensitivity: 103 dB SPL @ 1W1M - Frequency Response: -6dB @ 40 Hz and 12KHz

8x custom 8" Celestion drivers - (1) Le Son TLX-1 Piezo tweeter - Power Handling: Impedance: 480 Watts RMS 4 Ohms - Frequency Response: Suggested Amplifiers:
-6dB @ 35Hz and 16KHz SM-400S, Bass 350, Workingman's 4004

500 Watts Power Amps + PreAmps.

Dual channel amp head, 2x450 watts RMS into 4 ohms, MOSFET, 19", 3U. Extremely low-noise input section with gain control.

EBS Fafner, a glowing creation in laquered steel, chrome and bakelit, with tubes, transistors and a powerful accelerated 620 W MOSFET poweramp! EBS Fafner is made by bassists for bassists, for use in the roughest conditions imaginable - year after year without any trouble.